How to Replace a UPVC Window Handle

Don't be worried in the event that your upvc window handle is broken. Replacing a window handle made from upvc is an easy task and can be accomplished in a matter of a few steps.

It doesn't matter if you have an in-line or a cranked espagnolette window handle, they all have a square spindle that protrudes from the back plate. This spindle is then placed into the locking device.

Identify the lock type and handle

Over time, window handles or locks may be damaged and lose their functionality. The good thing is that this issue can often be remedied without replacing the entire uPVC window unit. One of the first things to do is to determine the kind of lock and handle you have because this will help determine the replacement parts you will need.

You can identify the type of handle by looking at the base. A screw or pin will hold the handle to its base. If the screw is not present it could be an indication that the handle has split off from its base section. If the handle has split internally and does not hold the spindle any longer, it may also be an indication that the handle must be replaced.

There are many uPVC handles however the Espag handle is the most well-known. These are typically fixed using two bolts, and come with an articulating spindle that is connected to the lock mechanism within the window frame. These handles are usually used on uPVC tilt and turn windows.

Another type of uPVC window handle is the Cockspur handle. They are similar to the Espag handle, but they have a lower projection from the frame. These handles are typically used on older uPVC windows.

Finally, there are also Venetian window handles, which are similar to the Espag handle, but they have a flat base that allows them to be placed in a flush position with the frame. These handles are a good choice for homeowners looking for an elegant handle that can blend with their uPVC frames. These handles are also available in a wide range of colours to match any decor.

Find the spindle's measurement.

Before ordering a new handle, it's important to know how the old one is connected. This will tell you how tight or loose it is and if it will be able to fit into the window frame. It is done by identifying the kind of handle you own and measuring the length of the spindle. The spindle is a metallic shaft that connects your handle to the lock inside the window frame. The spindle comes in a variety of sizes. The current standard for the industry is 8mm. Older handles could have 9mm of cross-section, so you'll have to measure your old handle to make sure that you have the correct size replacement.

There are several types of window handles, but the most popular are inline Espagnolette and cockspur handles. They operate a locking mechanism in the window using shootbolt rods which secure the window when it's closed. They are held in place by pins or screws depending on the type of handle you have.

You can find replacement handles for windows upvc window handles online and in most DIY stores. They are available in a variety of finishes, and can be used for windows that are new or replacement. They can also be key-locking or fire-escape non-locking for additional security.

To remove the old handle, simply open the window to the door and remove all the screws holding it in place. Be careful not to damage the screws, and put them in a container for later use. Once the screws have been removed, carefully remove the handle and measure from the base to the top of the spindle. This will provide you with the information needed to buy the right replacement. The spindle of the handle is the metal shaft that connects it to the lock gearbox in the window frame.

Remove the old handle

Changing the uPVC window handle is an easy task that typically will take no more than five minutes using the proper tools. The first thing to determine is the size and type of the handle or lock. This will help you select the appropriate replacement. After that, measuring the spindle will help ensure that the new handle is a suitable for the job. The old handle will need to be removed and replaced with the new.

Most uPVC handles come with inline Espagnolette handles. These handles have central spindles that slot into the locking mechanism of the window. These are generally easy to remove, but you may need to use force if they're stuck. The handle is usually held in place by two screws, which you can remove by using the help of a screwdriver. It is also possible to remove pins, depending on the kind of handle.

After removing the screws, you can then remove the handle you were using previously. If the handle is unlocked the top of the baseplate will be visible. It will reveal two additional screws that can be unscrewed. There's also a small silver or other colour sticker that has to be removed if it's still in place.

With the screws that came off the handle, you can now screw the new handle into the appropriate position. Make sure the handle is in an unlocked or open position, then align the screw holes to those on the window. After you've done this then replace the screw caps. Test the new handle. Changing a uPVC window can be a simple and quick task, but it's crucial to take the time to complete the task correctly.

Install the new handle

It's time for you to install your new handle if you've successfully removed the old one from the frame. Begin by locating the screw covers and then lifting them out using a screwdriver. Once the screw covers have been removed, store them in a safe place before moving on to the next step.

Then, you can insert the new spindle into the handle by lining it up with the existing hole and screwing it into. Be sure to align the holes of the handle with holes in the window frame and use a screw of the same length as the one used before or it could cause the handle to not being secure.

uPVC Espag handles are fitted with a 7mm square spindle that turns the lock mechanism that is fitted to the window. This type of handle can be commonly found in modern uPVC windows. uPVC Cockspur (also called by the name Cotswold) handles have an extended, curved nose that locks onto the outer frame or cross member of the transom bar. They are often found on older uPVC Windows.

It's important to lock and unlock the window several times after the handle is installed. If everything goes to plan, your replacement uPVC window handle should be securely attached and operating smoothly. If you have any problems this guideline will help you determine the cause and resolve it quickly. Bridgewater Glass can help you in the event of problems with your uPVC handles or any other home improvement that is glazed. Our glaziers have been trained to repair or replace various window frames and handles which makes us a great choice for your double-glazing needs.

Test the new handle

Over time and residential through normal use the uPVC locks and handles may be damaged and wear and wear and. This can leave them less effective and secure which is why it's crucial to replace them as quickly as possible. It's also a good idea to do this when you upgrade your windows, as changing your handle and lock will help maintain the integrity of your new windows.

When it is about uPVC window handles, there are many different styles. Some are secured with pins or screws, whereas others have blades that slot into the lock mechanism. Each lock type has its own way to replace it, and you'll need to know which type you own.

Espag window handles are the most well-known kind, and are typically found on newer uPVC windows. The spindle extends from the handle into the lock gearbox and residential activates the locking mechanism when you open the window. These handles are also easy to take off. However, you must be careful not to harm either the mechanism or the handle.

Cockspur handles are another alternative to uPVC window handles. They're held by a spur that is snagged onto an elongated striker plate that is attached to the frame. When you shut or tilt the window, it triggers the locking mechanism. This kind of handle is more difficult to repair than other types, but it's still an excellent choice for the majority of homes.

Venetian window handles are held by two bolts and feature an elongated projection from the frame, which is not the case with the Espag handle. These handles are ideal when you want to have a flush handle that blends into uPVC window frames. They're an excellent choice for commercial and residential buildings.