Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. They don't rot or rust like timber and aluminum.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home, and could even be fatal. It is essential to take the time to ensure that you're doing everything you can to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. If you have double-paned windows which are joined by internal beading, it will be difficult to remove and replace the old panes. In this case you'll need to source some plastic spacers that will aid the new pane in being able to fit properly into the frame of the window.

If you are going to attempt to remove the window panes by yourself it is important to wear appropriate safety gear, including thick gloves and eye protection. It is also an excellent idea to lay down a dropcloth before you start working on the glass to ensure that any fragments of glass fall onto the fabric instead of onto the floor, where they could be trampled on and cause further damage.

Once the glass has been removed from the window, it's best to seal the gap with packaging tape or duct tape to prevent water and drafts from getting into the property until a professional can come out and repair my windows and doors the window. This will also provide a barrier to prevent any criminals from getting into your home. If the gap between the door and the window is large, you might need to consider security screens that has windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber sash windows. In time, they could develop a variety of issues, including sagging. A sagging uPVC window can cause issues with light, draughts and even security. It's important to take action as soon as you discover that your uPVC windows are falling down.

To fix a window that is sagging you can try to reposition the hinges. To do this, you'll have to open the window so that you can access the frame. Then, using an screwdriver, unscrew the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have repositioned your hinges. If you're satisfied with the size of the window, you can tighten screws to hold them in the right position.

If you are unable to reposition the hinges, you might have to replace the seal. Seals made of rubber can dry out and window doctor near me lose their elasticity with time, which causes them to lose their tightness. It is important to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. The majority of the time, this is caused by screws that have become loose over time. However, it can occur because the handle mechanism has been worn out. Luckily, it's not difficult to repair the loose uPVC Window Doctor Near Me handle yourself. You'll first need to close the window and perform an initial fitting. The joint at the corner of the sash should be aligned with the joint on the casing. If it doesn't you can use a screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home and also hinder your ability to control the temperature inside your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or is missing.

This is a relatively easy fix that can be completed by any DIY expert. Based on the severity of the problem the caulking that was used up may need to be removed before a fresh layer can be put on. When it comes to uPVC repair, you should avoid 'over-caulking'. This can make your window more difficult to clean and reduce its energy efficiency.

It is crucial to make sure that the drainage holes are free of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious cases, you may need to replace the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in damp conditions and can quickly spread across the house.

If the leakage occurs between the double-glazed window, it is more likely that the issue is related to the seal, not the frame. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with ease, it may be the hinges that are at fault. These are easily repaired by any DIYer who is skilled and can be completed in a matter of minutes.

Like any mechanical component hinges are prone to be damaged over time. The process of replacing a hinge on a window is essentially a very simple procedure, but it is easier if you have someone to help you hold the frame up.

Verify that the uPVC hinges open and close in the right direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window a certain manner or because of poor installation at the factory. This can often be resolved by sending us a picture via our website and we will be more than happy to give you advice.

It is also crucial to grease the hinges on a regular basis. Applying a light engineering lubricant to the hinges is an ideal method of doing this. We recommend using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. This should be done at least every year. WD40 and other solvent-based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by several different things. The hinges, also because of wear and tear, could become misaligned. This can cause an opening to appear where the sash meets the frame. These can be easily repaired by giving them good clean, but in the event that they are beyond repair it may be necessary to get them re-aligned or replaced. The interlock, which is located on the hinge side of the window, can also become misaligned, again it is feasible to give them a good clean, but in some instances it could be necessary to get them replaced.

The next most common reason for draughts is window seals. These are susceptible to being worn out or damaged over time and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with low-emissivity glass, which will help regulate indoor temperatures and will lessen draughts.

One of the most effective methods to reduce draughts is by using an draught excluder. These are typically made of fabric that are filled with some type of filler. They can be placed on the windowsill on top. They can keep your home warm by blocking out cold air.

Your upvc windows can remain a great source of insulation and security for your home by performing regular maintenance and repairs. However, it is important to realize that all windows have a lifespan and eventually, they will reach a point where it is more efficient to replace them than repair them. If you are experiencing issues with your upvc window you should consult a professional as soon as possible.